Your cart is empty.
Your cart is empty.Product Description
UNIQUE INTEGRAL STRUCTURE
The magazine is integral to the gun body, with steel top cap, this staple gun looks like a hammer, give you a strong and reliable performance
Simple and compact structure offers optimum ease of use, while the lightweight body combined with the rubber-lined handle limit fatigue during long days on the job, you will be fun doing it.
What's in the Box
- 2000 - 1/4" length staples
- 2000 - 3/8" length staples
- 2000 - 5/8" length staples
- Allen wrench and Small bottle of tool oil
Quick Start Guide
Lubricate the Stapler
Put 3-5 drops of pneumatic tool oil into the fitting before use. Reconnect the air hose and the stapler and proceed to pull the trigger at least five times to spread the oil through the parts of the gun. Add a few drops more after each hour of continual use.
TIP ●Only use lubricating oil made specifically for pneumatic tools, such as pneumatic tool oil. Keep the WD40, compressor oil, motor oil, transmission fluid, etc. out of your air staplers.
Connect to Compressor
Set your compressor to 90 PSI and use your air hose's quick-connect fitting to connect your tool. If you need to, you can safely increase the pressure up to 110 PSI.
TIPS ●Staple guns, as a general rule, don’t need a lot in the way of air volume or CFM, and even smaller portable air compressors can get by with their smaller tanks as long as it’s just one staple gun. ●To get the best performance, requires minimum 3/4 hp or 3 gallons Compressor.
Loading Staple Gun
With the stapler upside down, squeeze the release button at the rear and slide open the magazine. Insert the staple strip with the sharp edge pointing towards the nose of the gun and carefully slide the magazine closed until it locks into position.
TIP ●To ensure that you’ve properly loaded the staples; you should use a piece of wood to testing. After pulling the trigger, check out if there’s one clean staple on the wood–if there is, everything is working correctly.
Stapling Like a Pro
This gun have a dual trigger actuation system. The secondary trigger must be pulled in order to pull the primary trigger. Load the gun with staples, and connect the gun to an air supply. Press the nose of the tool against the work piece, pull the dual triggers to drive a staple.
TIPS ●Each time the primary trigger is pulled, the tool will drive a staple. ●You can increase or decrease the outlet pressure to control how deep the staple gun drives the staples.
Steve
Reviewed in the United States on March 3, 2025
My kitchen chairs upholstering job was completed quickly with this staple gun. Thee gun drove staples without a problem. The only issue was the design of the trigger's safety latch, it was not user friendly and clumsy to use.
Carlos Luis Torres Molina
Reviewed in the United States on March 13, 2025
Magnífica espectacular para el trabajo de tapicería
Roxy
Reviewed in Canada on September 29, 2024
I just tried to put a few staples in hard wood and is always jams up or doesn’t fire at all
DK
Reviewed in the United States on September 25, 2024
Took me awhile to figure out what was wrong. The bar that retracts to push the next staple forward never returned far enough by itself to push the next staple. In order to complete my job which I had to complete that very day it arrived, I had to push the bar back far enough with a screwdriver.I had to do this each time I stapled. I had to open the staple holding section each time as well.Truly a Pc of crap. I did get my job done, but it took an extra two hours and I cut my hand twice and threw it away.Wonder if these staples fit anything else in the stapler world? I kept them.
Mike Adair
Reviewed in Canada on August 19, 2024
Great for re upholstery chairs I had. No issues
Bob
Reviewed in the United States on August 14, 2024
liked replace seat cover on seadoo
Sundog
Reviewed in Canada on July 23, 2024
Worked great for the first hour then it starting leaking air out the front. An internal o-ring blew out.A waste of money.
Steen nielsen
Reviewed in Canada on October 1, 2024
This is probably the worst upholstery stapler I have ever used the staples either jam or fallout of the gun in clumps they are to tho and the trigger guard is a pain not worth the money there are many better staple gins in this price range waste of money
Ricardo Villagomez Tamez
Reviewed in Mexico on August 21, 2023
este aparato funciona perfectamente bien. lo recomiendo ampliamente.
Aaron Seaton
Reviewed in Canada on July 2, 2022
This is a cheap, garbage product that failed to work out of the box. I never even had the chance to drive one staple with it. Pressing the trigger just causes error to leak out where the staple should be discharged. The driver pin seems to be seized or the internal air seals are leaking. Unfortunately I didn't discover this until my return window closed. Lesson learned. Folks, don't buy this. Spend a few bucks more and get the Arrow or another well engineered product.
Chevyman
Reviewed in Canada on November 5, 2022
was skeptical thinking how well would this machine perform because of the price.....it worked flawlessly on the custom 7 foot gaming table I built.rate it 5 stars out of 5!
Bundjames007
Reviewed in Canada on December 3, 2021
Great tool, working like a charm. But, hard to find staples to fit.
allan w.
Reviewed in Canada on October 1, 2020
Jams constantly, particularly if the staple strip is getting low or has a break in it. I should have tested it out as soon as I received it so I could have returned it. I am replacing it with a WEN.
Recommended Products
$125.60
$ 53 .99 $53.99
$113.66
$ 56 .15 $56.15