Your cart is empty.
Your cart is empty.
Fitment:
Compatible with BMW
Fit F800GS (Standard & Adventure Models) All Years
Fit F800GT All Years
Fit F850GS 2019 - Newer
Fit K1600B / K1600 Grand America (Black Trim ONLY!) 2018 and Newer
Fit R1200GS (Air/Oil Cooled; Standard & Adventure Models) 2012 and Older
Fit R1200R 2011-2014
Fit R nineT All Years
Fit S1000R 2013-Newer
Compatible with Triumph
Fit Scrambler 2017 & Newer
Fit Speed/Street Triple 2008 & Newer
Fit Tiger 800 XC/XCS 2011 & Newer
Fit Tiger 800 Street/Roadie 2011 & Newer
Fit Tiger 1200 Explorer All Years
Compatible with Yamaha
Fit FJ09 All Years
Fit FZ09 / FZ10 All Years
Fit Vmax All Years
Fit Super Tenere 2013 & Older
Fit Super Tenere 2014 & Newer
Fit XSR 900 2016 & Newer
Compatible with Ducati
Fit Hypermotard All Years
Fit Monster 796 / 1100 / 1200 All Years
Fit Multistrada 2008-2014
Fit Multistrada 950/1200 2015 & Newer
Compatible with Honda
Fit Africa Twin 2016 & Newer
Fit CB 300/500 2019 and Newer
Fit CTX 700/1300 All Years
Compatible with Kawasaki
Fit Versy 1000 2015 & Newer
Fit Z1000 All Years
Fit Others
Compatible with Moto Guzzi
Fit Stelvio 1200 All Years
Compatible with Suzuki
DL1000XT V-Strom 2018
Compatible with Aprilia
Tuono V4 1100 Factory KG above 2016
Compatible with Honda
CB 1000 R SC 60 2010-2016
Compatible with Can-Am
Spyder F3 (works on F3 models ONLY!) 2015 & Newer
Fit 250, 300XC, 350EXC/XC/SX, 450EXC/SX/XC, 500EXC/XC All Years
Fit 690 E and 690 R All Years
Fit 990/950 Adventure/Adventure Baja/Super Enduro All Years
Fit 1090/1190/1290 Adventure and Super ADV All Years
Fit Super Duke 1290 All Years
Corie
Reviewed in Canada on June 6, 2024
Nice machining.
Dan
Reviewed in Canada on June 29, 2024
Material seats well in the semi circle on the bmw 800gs stock handle bar mounts. The good stops there though, too much material machined away on the shoulders. Gap of .040” on either side. Creates a rocking motion when you pull with mild to medium pull on the bars. Upper bar opening is too small as someone else posted about. .055” gap under the stock bmw 1.125” bars when they sit cradled in the under machined profile.You could try and get away with this on a dirt bike but man, if you’re a big person and doing over 50km you don’t want to lose your bars.Garbage. So much for a last minute save before a week long BDR run. 👎
John McHan
Reviewed in the United States on June 20, 2024
These were perfect for my bike (DL1000). They brought the bars up and back a little without having to reroute any cables or hoses. The moderate rise of the bars is just enough to make the bike more comfortable which I tested with an 1100 mile trip.Well worth the money and installation.
susan cristian
Reviewed in Germany on June 2, 2024
HalloBitte eine Adresse hier lassen für Zürich schicken weil passt nicht für Can Am
stephane
Reviewed in Canada on May 19, 2024
f3 has angle in the blocks.....these are plain straight and not even long enough
robert schools
Reviewed in the United States on November 20, 2024
Worked out good no tight cables
Sinbad
Reviewed in the United States on August 9, 2022
perfect fit on 22 KLX 300, did nothing to wires,hoses or cables. 15 minute install, allen head bolt were right length.put 1 side on & finer start 2 bolts. then lift bar into other & repeat. tighten at comfortable angle for you. low cost, easy to remove if you don't like them. would buy again.
Ghost
Reviewed in the United States on October 23, 2022
Risers work well but hardware is short and didn't reach the threaded holes. Luckily had some hardware that fit otherwise I would've had to buy new hardware. I hope the seller looks into this issue and corrects it.
Recommended Products
