Your cart is empty.
Your cart is empty.Product Description
Vgate 6x1/0 AWG Gauge Post Terminals for Lithium or AGM Lead Acid Battery with Bolt Down Ends or Threaded Studs M10 or 3/8”-16
Unlike other common brands of castings, Vgate battery terminal clamps are machined from 6061 aluminum. In addition to high precision, it also has high toughness and good corrosion resistance.
- To neatening up wire installation and clean up cluttered battery terminals;
- Coming in pairs (one positive, one negative) (+/-);
- The 6-hole holders exactly to hold 1/0 AWG (0 gauge) welding wire, which is bare or with ferrule terminal, and also can hook up other gauge wire (less than 1/0 AWG): 2 AWG, 4 AWG, 6 AWG, 8 AWG and so on, but the size of holders are bigger than the said gauges.
Application for Following Batteries:
- Battery Type: Lithium and Lead Acid Batteries (AGM, GEL, WET, MF and CA/CA)
- Battery Voltage: 48V 36V 24V 12V 6V
- Battery for: Car, Caravan, Motorhome, RV, Bus, Truck, Pickup, Houseboat, Motorcycle, Forklift, Crane, Solar Power Bank and more others.
Package Includes：
- 1 x Positive Terminal & 1 x Negative Terminal
- Bolt (Inch and mm 2pcs/each)
- Nut (Inch and mm 2pcs/each)
- Flat (8pcs) & Spring (2pcs) Washer
Product Details
Work with Various Gauge
- Vgate 6-hole holders exactly to hold 0 (1/0) AWG welding cable, and also can hold other gauge cables: 2 AWG, 4 AWG, 6 AWG, 8 AWG and so on.
Additional Parts
- The screw has Clear thread which is easy to use.
- Parts Included:
Bolt (Inch and mm 2pcs/each),
Nut (Inch and mm 2pcs/each),
Flat (8pcs) & Spring (2pcs) Washer
Battery Post Type
- Battery Type: Lithium and Lead Acid Batteries (AGM, GEL, WET, MF and CA/CA)
- Bolt Down Ends or Threaded Stud;
Remark: Bolt Down Ends including Top Post and Side Post.
- Post Size: M10 or 3/8”-16
Please install the metal washers according to the actual usage to ensure a firm installation.
K
Reviewed in Canada on November 11, 2024
Great for wiring in accessories in vehicle
Billy Cairns
Reviewed in Canada on September 26, 2022
Used on my boat wiring to tidy up with secure connection.
ROBERT PA
Reviewed in the United States on July 23, 2022
I like that it makes it easy to connect many large gauge wires to a battery. Kind of pricey for being machined aluminum, would prefer copper for maximum conductivity. Overall very nice and I will buy more when needed.
Rowdy
Reviewed in the United States on February 6, 2022
Great for multiply wiring going to a battery. I used it on my boat. It should cut down on corrosion.
Samuel Holland
Reviewed in the United States on November 28, 2022
It came in a nice looking box and had two sets of mounting hardware. Thanks
the canadians
Reviewed in Canada on November 3, 2021
worked well for multiple grounds ininstrument housing
Patrick M. Walker
Reviewed in the United States on November 16, 2021
Very nice looking, excellent workmanship, really cleaned up the mess of accessory wires connected to the battery on my sideburns side RZR.
henry hofmeister
Reviewed in the United States on October 16, 2021
awesome machining. the negative isn't necessary unless maybe a bad body ground in unibody? nobody needs 6 humongous wire holes on both pos & neg (especially on a side post application? WTF?) so i wish there were 1 big and 5 smaller gauge. overall the makers did really good on quality, not so much on fitting the needs of the average enthusiast.
Devin j
Reviewed in Canada on April 18, 2021
Awesome product easy to add to battery looks great
Recommended Products
$65.58
$ 25 .91 $25.91
$68.82
$ 31 .67 $31.67
$35.27
$ 15 .83 $15.83